How often must the exposure control plan be reviewed and updated?

yearly
According to the OSHA Bloodborne Pathogens Standard, an Exposure Control Plan must meet certain criteria: It must be written specifically for each facility. It must be reviewed and updated at least yearly (to reflect changes such as new worker. positions or technology used to reduce exposures to blood or body fluids)

What is the purpose of exposure control plan?

To prevent or minimize the occupational exposure and potential infection of employees to hazards and blood-borne pathogens or other potentially infectious materials, (OPIM) and to assure compliance with the applicable provisions of policies set forth.

What is the purpose of the exposure control plan quizlet?

What is an Exposure Control Plan?

Each employer having employees with occupational exposure to bloodborne pathogens and Other Potential Infectious Materials must establish a written exposure control plan designed to eliminate or minimize employee exposure.

How long is the exposure control plan good for?

three years
These documents will be kept for at least three years at (Location of records). The training records include: The dates of the training sessions. The contents or a summary of the training sessions.
Reply #2: OSHAÕs bloodborne pathogens standard requires employers to review and update the Exposure Control Plan (ECP) at least annually [29 CFR 1910.1030(c)(1)(iv)], even those who currently use appropriate safety devices.

What is perhaps the most critical piece of PPE?

Gloves are the most commonly worn piece of PPE. Examples of when gloves must be worn are shown on this slide. Besides blood and body fluids, mucous membranes, non-intact skin and the insertion area of a patientÕs invasive device should only be touched with gloved hands.

What are the five steps of an exposure control plan?

Contact the Office of Risk Management for questions.
Step 1: Required Personal Protective Equipment.
Step 2: Equipment.
Step 3: Decontamination Procedures.
Step 4: Disposal.
Step 5: Decontaminate Re-useable Equipment.
Step 6: Wash Your Hands.

What are 3 main parts of an exposure control plan?

Elements of an Exposure Control Plan
Statement of purpose.
Responsibilities of the owner, prime, employer, designated resources (i.e. H&S Manager), supervisors, and workers.
Health hazards and risk categories for each product in your worksite.
Written work procedures and practices.

What are four examples of common engineering controls?

Examples include self-capping syringe needles, ventilation systems such as a fume hood, sound-dampening materials to reduce noise levels, safety interlocks, and radiation shielding.

What should be included in an exposure control plan quizlet?

An exposure control plan should include: > A list of job classifications for which occupational exposure control is applicable, such as medical assistant, lab technician, dental hygienist, etc. > A list of tasks during which exposure may occur.

What are the requirements for an exposure control plan?

Per the OSHA Bloodborne Pathogens Standard, an Exposure Control Plan must meet certain criteria: It must be written specifically for each facility. It must be reviewed and updated at least yearly to reflect changes such as new worker positions or technology used to reduce exposures to blood or body fluids.

What is the OSHA exposure control plan for bloodborne pathogens?

In pursuit of this goal, the following exposure control plan (ECP) is provided to eliminate or minimize occupational exposure to bloodborne pathogens in accordance with OSHA standard 29 CFR 1910.1030, ÒOccupational Exposure to Bloodborne Pathogens.Ó

How is occupational exposure classified in an ECP?

Occupational exposure is classified by the job or task, not by the individual. In addition to identifying the job classification and department, the ECP should also identify the procedures, or group of closely related tasks and procedures, in which occupational exposure may occur.
The control plan should be reviewed and updated with each level change or revision of the part or assembly. The control plan should be a living document. This section of the Control Plan describes the particular characteristics of the product or process that may need to be controlled and documented.

How often must a fire pump be no flow tested?

once a week
For electric motor-driven fire pumps, we recommend at least running your equipment once a week for at least ten (10) minutes for a visual inspection. You do not need to flow and measure water during this test Ñ just witness the equipment running and have someone qualified present to address any problems that may arise.

What is an annual fire pump test?

The annual fire pump flow test is a full test of a pumpÕs capabilities and is arguably the most critical test. It is conducted once a year to measure flow and pressure and make sure the fire pump is ready to respond to a call to service. A maximum of 140 percent of rated pressure at churn (no flow)

How do you measure fire pump GPM?

For example, if you have a 40,000-square-foot building that is all ordinary group 1, the calculation would be 1,500 x 0.15 (density) = 225 + 250 (hose demand) = 475 gpm total for the fire pump.

How often should a fire pump be tested?

According to NFPA 25, fire pumps must be tested on both a monthly and annual basis to ensure that they will perform as designed. These two different tests are referred to as a monthly ÒchurnÓ test and an annual flow test.

How can I test my water at home?

Often county health departments will help you test for bacteria or nitrates. If not, you can have your water tested by a state certified laboratory. You can find one in your area by calling the Safe Drinking Water Hotline at 800-426-4791 or visiting www.epa.gov/safewater/labs.

How long does a hydrant flow test take?

Attach pitot gauge to flow hydrant. Open hydrant; record pitot/flow gauge reading (flow for 2 minutes).

How does a fire water pump work?

The fire pump starts when the pressure in the fire sprinkler system drops below a certain set-point. If one or more fire sprinklers are exposed to heat above their design temperature, and opens, the sprinkler system pressure drops and the pressure switches gives a signal and the duty pump starts.

Can a fire pump test be conducted without flowing water?

Chapter five of NFPA 25 requires a weekly fire pump test to be conducted without flowing water. Does this include the circulation relief valve?

No. The standard says Òwithout flowing waterÓ so no one flows water at minimum, rated and peak flows each week as required for the annual flow test.

How is discharge pressure measured on a fire pump?

Then, adjust the flow rate through the flow meter until the same discharge pressure is obtained as earlier. The flow meter reading is then compared against the flow obtained with the pitot flow measurements.

How often should a fire pump churn test be performed?

These two different tests are referred to as a monthly ÒchurnÓ test and an annual flow test. Annual Fire Pump Flow Test The fire pump flow test is required by NFPA 25 to be conducted once a year in order to measure the pumpÕs flow and pressure. The test should be performed by attaching hoses to the discharge test header.

What do you need for fire flow testing?

Fire flow testing is a relatively easy procedure. To conduct a fire flow test, the following equipment is needed: two fire hydrants with at least one 2 1/2-inch nozzle butt on each. a map of the water supply piping serving the hydrants. pitot gauge. 2Õ/2-inch cap gauge with bleedoff cock. hvdrant wrench. ruler accurate to Ô/Winch.

Leave a Comment

Your email address will not be published.

Scroll to Top